DS8000 Service Documentation Version 8.5.7

Assembling a Model 983 in a rack

Assemble a Model 983 in a customer rack.

Section-1, List of sections
The table that follows provides an overview of the sequence of required and optional tasks to install the Model 983 into a customer provided rack.
Section-2, Overview
Section-3, Two system service representatives are required to install this system
Section-4, Unpacking and verifying that the ship group is complete
Section-5, Checking the prerequisites on the customer provided rack
Section-6, Installing the 4U rails for the UPS (E61 and E62)
Section-7, Installing the lower UPS (E62) on the 4U Rails
Section-8, Installing the upper UPS (E61) on the 4U rails
Section-9, Installing the rails for the management enclosure
Section-10, Installing the cable management arm support
Section-11, Cable bundle 1, Installing the cable management arm, latching front and rear
Section-12, Installing the management enclosure on the rails
Section-13, Cable bundle 1, connecting to the management enclosure
Section-14, Cable bundle 1, separating the cable groups hanging down
Section-15, Cable bundle 1, installing the UPS cable tie bar
Section-16, Cable bundle 1, connecting green to upper UPS (E61) and yellow to lower UPS (E62)
Section-17, Installing the rails for the lower CEC enclosure (XC2)
Section-18, Installing the lower CEC enclosure (XC2) on the rails
Section-19, Cable bundle 1, installing the lower CEC enclosure (XC2) cable tie bar and connecting cables
Section-20, Installing the rails for the upper CEC enclosure (XC1)
Section-21, Installing the upper CEC enclosure (XC1) on the rails
Section-22, Cable bundle 1, installing the upper CEC enclosure (XC1) cable tie bar and connecting cables
Section-23, Installing the rails for the I/O enclosure (IG3/1G4)
Section-24, Installing the I/O enclosure (IG3/1G4) on the rails and installing the front bezel
Section-25, Installing the rails for the lower flash enclosure (I1-F04)
Section-26, Cable bundle 2, Installing the I/O enclosure (1G3/1G4) cable tie bar and connecting cables
Section-27, Cable bundle 2, Connecting to the upper CEC enclosure (XC1)
Section-28, Cable bundle 2, Connecting to the lower CEC enclosure (XC2)
Section-29, Cable bundle 2, connecting green to upper UPS (E61) and yellow to lower UPS (E62)
Section-30, Cable Bundle 1, Connecting to I/O enclosure (1G3/1G4)
Section-31, Installing the lower flash enclosure (I1-F04) on the rails
Section-32, Installing the rails for the upper flash enclosure (I1-F03)
Section-33, Installing the upper flash enclosure (I1-F03) on the rails
Section-34, Cable bundle 3, installing cable tie bar at upper flash enclosure I1-F03
Section-35, Cable bundle 3, connecting to the lower flash enclosure (I1-F04)
Section-36, Cable bundle 3, connecting to the upper flash enclosure (I1-F03)
Section-37, Cable bundle 3, connecting to the I/O enclosure (1G3/1G4)
Section-38, Cable bundle 3, connecting green to upper UPS (E61) and yellow to lower UPS (E62)
Section-39, Cable bundle 4, connecting to the I/O enclosure (I1-G3/G4) (optional feature)
Section-40, Cable bundle 4, connecting to the upper CEC enclosure (XC1) (optional feature)
Section-41, Cable bundle 4, connecting to the lower CEC enclosure (XC2) (optional feature)
Section-42, Installing the FC 1765 keyboard display (optional feature)
Section-43, Connecting the keyboard display
Section-44, Routing the mainline power cables, not connecting to the UPS
Section-45, Storing the service items
Section-46, Completing the Model 983 assembly in the rack
Section-47, Reference

Parent topic: Start here for all installation and remove tasks (Models 98x, 8xE)